Hotbins
Spec Offline
Member
#81
Looking for some thoughts, I have aquiered some insulation paneling, some of which I will need to glue together, all clean square cuts so no problem glueing them, but would it be any advantage sticking them onto thin exterior plywood and if you think yes should it go on the inside or the outside of a home made hot bin
[-] The following 1 user Likes Spec's post:
  • Can the Man
Reply

Spec Offline
Member
#82
Veggie what size is the vent hole on the lid of your hotbox and can it be shut off
[-] The following 1 user Likes Spec's post:
  • Can the Man
Reply

Veggie Offline
Super Pest Controller
#83
(31-01-2021, 10:21 PM)Spec Wrote: Looking for some thoughts, I have aquiered some insulation paneling, some of which I will need to glue together, all clean square cuts so no problem glueing them, but would it be any advantage sticking them onto thin exterior plywood and if you think yes should it go on the inside or the outside of a home made hot bin
There's condensation inside the bin, so plywood might rot?
The Moneyless Chicken says:- 
Use it up, wear it out, make it do or do without.
[-] The following 2 users Like Veggie's post:
  • Can the Man, Spec
Reply

Veggie Offline
Super Pest Controller
#84
          

Hope this helps!! Its like a butterfly valve  in a carburettor. Its at the recommended angle at the moment.
The Moneyless Chicken says:- 
Use it up, wear it out, make it do or do without.
[-] The following 2 users Like Veggie's post:
  • Can the Man, Spec
Reply

Broadway Offline
Member
#85
Here is the first pic of my ongoing attempt, I reckon its about 40% complete.

Looking at the front panel it needs to move up so the gap is at the bottom, this first gap is to remove the tray that will hopefully catch the liquid.

Another section needs to be cut from the front to view/remove ready compost. I'd like to say the three section front was a genius idea by me but no, the first section I cut was too small!

I've not done anything on it for a few weeks as me and No.2 kept losing patience with one anotherSmile

The bottom, top, and inside sections have been cut but may need amending.

The straight uncut edges are at the bottom, the cut edges at the top hence it looks a bit squint!

As it's supposedly raining/snowing for most of tomorrow it's back on the agenda, this time I will need to break Mrs B's spiritSmile
   
Regards..........Danny Smile
[-] The following 3 users Like Broadway's post:
  • Can the Man, JJB, Veggie
Reply

Veggie Offline
Super Pest Controller
#86
Mr Greedy has settled in a comfy pattern - 35C on his head and 50C in his tummy.Smile
He's making me very happy. Wink
The Moneyless Chicken says:- 
Use it up, wear it out, make it do or do without.
[-] The following 6 users Like Veggie's post:
  • Bren, Can the Man, JJB, Mark_Riga, Small chilli, Spec
Reply

Veggie Offline
Super Pest Controller
#87
Mr Greedy wants to show you his innards!!

   

    Top Thermometer

    Contents Thermometer so steamed up you can't read the temp!!
The Moneyless Chicken says:- 
Use it up, wear it out, make it do or do without.
[-] The following 3 users Like Veggie's post:
  • Can the Man, Small chilli, toomanytommytoes
Reply

Broadway Offline
Member
#88
(18-02-2021, 02:25 PM)Veggie Wrote: Mr Greedy wants to show you his innards!!



Top Thermometer

Contents Thermometer so steamed up you can't read the temp!!
Looking good VeggieSmile
Regards..........Danny Smile
[-] The following 2 users Like Broadway's post:
  • Can the Man, Veggie
Reply

JJB Offline
Moonraker
#89
I take it you're well pleased with Mr Greedy's progress and usefulness.
Gardening is an excuse not to do housework
Greetings from Salisbury
Qualified member of the Confused Nutter's Club 
[-] The following 2 users Like JJB's post:
  • Can the Man, Veggie
Reply

Veggie Offline
Super Pest Controller
#90
So far, so good, JJB.Smile
The Moneyless Chicken says:- 
Use it up, wear it out, make it do or do without.
[-] The following 2 users Like Veggie's post:
  • Can the Man, JJB
Reply





Users browsing this thread:
3 Guest(s)



Theme © iAndrew 2018 - Forum software by © MyBB .